本公司5月8號09點24分報道：TCJT-32型低溫脆性試驗儀價格@企業動態
產品簡介
YI、TCJT-32型低溫脆性試驗儀概述：
YI、TCJT-32型低溫脆性試驗儀概述：
TCJT-32型橡膠、塑料（定制）低溫脆性試驗儀是測定材料在規定條件下試樣受沖擊出現破壞時的溫度，即為脆性溫度，可以對塑料及其他彈性材料在低溫條件下的使用性能作比較性鑒定。可以測定不同橡膠材料或不同配方的硫化橡膠的脆性溫度和低溫性能的優劣。因此無論在科學研究材料及其他制品的質量檢驗，生產過程的控制等方面均是的。本儀器是依據GB1682、JTGE50標準設計的，各項技術指標符合GB/T 15256硫化橡膠或熱塑性橡膠低溫脆性的測定（多試樣法）標準的要求。
Overview of tcjt-32 low temperature brittleness tester:
Tcjt-32 low temperature brittleness tester for rubber and plastics (customized) is used to measure the temperature at which the specimen is damaged under impact under specified conditions, that is, the brittleness temperature. It can be used to comparatively identify the performance of plastics and other elastic materials under low temperature conditions. It can measure the brittleness temperature and low temperature performance of vulcanized rubber with different rubber materials or different formulations. Therefore, no matter in scientific research materials and other products quality inspection, production process control are indispensable. The instrument is designed according to the standards of GB 1682 and jtge50. All technical indexes meet the requirements of GB / T 15256 standard for determination of low temperature brittleness of vulcanized rubber or thermoplastic rubber (multi sample method).
技術參數
二、TCJT-32型低溫脆性試驗儀技術參數：
二、TCJT-32型低溫脆性試驗儀技術參數：
1、試驗溫度及時間：-70℃降溫時間短，無需水冷卻，更環保
2、沖擊速度：2m/s±0.2m/s
3、恒溫后，試驗3min時間內溫度波動：＜±0.5℃波動小，控溫更
4、沖擊頭半徑為1.6mm±0.1mm
5、在沖擊時沖擊頭和試樣夾持器的間隙為6.4mm±0.3mm
6、沖擊頭的沖擊和試樣夾持器直間的距離為8mm±0.3mm
7、功率：800W，功率更小，達到溫度后壓縮機還有自動停機，更環保節能
8、容積：3500ml容積更大，測試范圍更廣
9、外型尺寸：800×550×1100mm
10、整機重量：120Kg
Technical parameters of tcjt-32 low temperature brittleness tester:
1. Test temperature and time: - 70 ℃ cooling time is short, no water cooling, more environmental protection
2. Impact velocity: 2m / S ± 0.2m/s
3. After constant temperature, temperature fluctuation within 3 min of test: ＜ 0 ± 0.5 ℃ fluctuation is small, temperature control is more accurate
4. The radius of impact head is 1.6 mm ± 0.1mm
5. The gap between the impactor and the sample holder is 6.4mm ± 0.3mm
6. The distance between the impact of the impactor and the sample holder is 8mm ± 0.3mm
7. Power: 800W, smaller power, when reaching the temperature, the compressor will s automatically, more environmental protection and energy saving
8. Volume: 3500ml, larger volume, wider test range
9. Size: 800 × five hundred and fifty × 1100mm
10. Total weight: 120kg
公司介紹
主營產品：土工檢測儀器,防水材料檢測儀器,陶瓷磚檢測儀器,水利水電粗粒土系列,瀝青儀器檢測儀器
主營產品：土工檢測儀器,防水材料檢測儀器,陶瓷磚檢測儀器,水利水電粗粒土系列,瀝青儀器檢測儀器
Main products: geotechnical testing instrument, waterproof material testing instrument, ceramic brick testing instrument, water conservancy and hydropower coarse-grained soil series, asphalt testing instrument
所有評論僅代表網友意見，與本站立場無關。